Hi,
Why is it not possible to enter values (variables)
for the frame rate in key frames in the speed effect?
(only with mouse!) For values below 0.25
working with the mouse becomes a hassle!
Thanks!
Hi
The Speed factor and Frames rate settings are linked, you can only use one or the other.
Speed factor values less than 0.25 and greater than 4.0 are not possible when the clip has audio attached.
The warning message to detach/remove the audio, unless you have turned off the error message, should appear.
John EB
Forum Moderator
Hi
in this case, the audio is not part of it!
These situations below 0.25 and above 4.00
(without audio)
See that in the end all the work is lost from
the moment I use the icon that adjusts the length
of the clip in the example the video below:
characterizes program inconsistency or illogicality!
Roberto, I would think that the designers would not expect that someone would go to the trouble of setting speed keyframes then use the Object Stretch mouse mode. What would be the point?
If that indeed is what you want, a workaround would be to set up the various keyframes as you did, then export that section and bring it back in and apply the Object Stretch mouse mode to the length you desire.
Note that it is normal to work with low frame rates to build, for example, a speed ramp or, in my case, I use speed to correct shakes and I can do it in many cases where the "native" stabilization effects cannot regularize. For example, Vegas Pro, since previous versions, has allowed the user to type the speed in the key frames, seeking precision and thus avoiding inconvenience as in the example I gave.
You can type the speed for each keyframe: just click the speed box, type in what you want, then hit Enter.
I thought the problem issue is the Object Stretch after you've set all the keyframes.
PS: Yet another example of the clumsy change at the time of the new SPR. You can't set an initial anchoring 1.00 speed keyframe because the keyframe control panel is greyed out. You have to set the play marker, set a different speed to 1.00, hit Enter (which creates a keyframe), then reset the speed at that keyframe back to 1.00.
After adding the keyframe, the program does not allow data entry in the frame rate field!
It should! But that is not what happens!
I ask you to confirm the latest version of VPX16 because despite having recorded it on MMS2024, the VPX16 of the "test" version installed on another machine here is 22.0.1.215 (UDC2)
Can you post the history of this version here?
Is this version exactly after version 22.0.1.244?
After adding the keyframe, the program does not allow data entry in the frame rate field!
It should! But that is not what happens!
Yes, sorry, you're right. Whether it "should" or not is the issue. The frame rate droplist is active when you haven't adjusted the speed (or reset the speed effect). It would be good if you could set the framerate. Perhaps put in a feature request to Support.
A bug I have found is that you can't adjust the speed of a keyframe by clicking the green box on the object (turning it yellow). The speed is adjusted for the keyframe that the Play marker is on, not the one you clicked. If the Play marker is in a blank area on the object, a new keyframe is created there.
Sorry, I have no information about the history of this version.
22.0.1.244 was the immediately-preceding version.
Jeff
Forum Moderator
I had opened a ticket with technical support referencing this post precisely because these issues deal with inconveniences and loss of work!
In this last version (244), if possible, see: create a clip on the timeline that is longer than 1 second (important). Transfer it to the project folder. Navigate to it in the project folder and play the playback from the source monitor and evaluate if it will play until the end corresponding to the created size. (If it only plays up to 1 second then they didn't fix the existing bug!)
Thanks!
Hi Roberto,
The did not fix the Project Temp Folder duration bug.
Please remind them and I'll do the same.
John CB
Hi and ok! All content in this topic is under the knowledge of technical support, through a ticket that I opened.
What I have to say: Magix please! Help us so that we can help you!
Thanks!