Comments

Brackets wrote on 2/2/2022, 9:05 PM

Just to clarify my example (I'm not sure I was that clear....): I'd like to use a plugin as a comfort reverb when tracking a vocal, but only be actually recording the naked vocal (i.e. without the reverb). Is this possible? If so, how?

SP. wrote on 2/3/2022, 6:01 AM

@Brackets Just disable the reverb plugin on your recorded track.

Yelandkeil wrote on 2/3/2022, 1:16 PM

 

Or insert a bus-track with reverb filter, then lead the output of your recording/midi track or what else to that reverb bus.

 

-- Hard- and Software for 5.1RealHDR10 --

ASUS TUF Gaming B550plus BIOS3202: 
*Thermaltake TOUGHPOWER GF1 850W 
*ADATA XPG GAMMIX S11PRO; 512GB/sys, 2TB/data 
*G.SKILL F4-3200C16Q-64GFX 
*AMD Ryzen9 5950x + LiquidFreezer II-240 
*XFX Speedster-MERC319-RX6900XT <-AdrenalinEdition 24.10.1
Windows11Pro: 23H2-22631.4541; Direct3D Driver: 9.17.11.0272

Samsung 2xLU28R55 HDR10 (300CD/m², 1499Nits/peak) ->2xDPort
LG DSP7 Surround 5.1Soundbar ->TOSLINK (AAFOptimusPack 6.0.9403.1)
ROCCAT Kave 5.1Headset/Mic ->Analog

DC-GH6/H-FS12060E_HLG4k120p: WB=manual, Shutter=125, ISO=auto
HERO5_ProtuneFlat2.7k60pLinear: WB=4800K, Shutter=auto, ISO=800

VEGASPro22/21 + XMediaRecode/Handbrake + DVDArchi7 
AcidPro10 + SoundForgePro14.0.065 + SpectraLayersPro7 
K-LitecodecPack17.8.0 (MPC Video Renderer for HDR10-Videoplayback on PC) 

Brackets wrote on 2/3/2022, 6:08 PM

Thanks for your replies, much appreciated!

I tried the two methods above and neither make any difference, in that I can only hear the mic and not the reverb.

I feel like there’s something fundamental that I’m doing wrong that would justifiably warrant a facepalm from everyone here. But I’ll leave my dignity at the door and continue!

My setup consists of a newly purchased 2nd hand focusrite 18i20 (that I’m still getting my head around!). I have a mic going straight into one of its channels.

I add an audio track in Acid Pro, add a reverb plugin to the track, and set the track to the appropriate 18i20 channel input.

The result is; I can hear the mic (and am able to record it) but I cannot hear the reverb plugin in real time as I’m tracking. And that’s what I’m after.

Apologies for being the noob in the room.

 

SP. wrote on 2/3/2022, 7:43 PM

@Brackets You have selected the Focusrite USB ASIO driver in the audio settings of ACID and connected your headphones to the headphone output or the speakers to the speaker output of the Focusrite interface?

Brackets wrote on 2/3/2022, 8:02 PM

@Brackets You have selected the Focusrite USB ASIO driver in the audio settings of ACID and connected your headphones to the headphone output or the speakers to the speaker output of the Focusrite interface?

Yep. I have the Focusrite USB ASIO driver selected in ACID, and I'm using one of the headphone outs on the interface for monitoring.

SP. wrote on 2/3/2022, 8:09 PM

@Brackets Have you checked if you are monitoring the output signal from your computer and not the input signal from your microphone before it goes into the computer? I don't know how the 18i20 works, but I would guess you can configure it.

shkr wrote on 2/4/2022, 4:24 AM

You need to use "input bus" and put reverb there. Than on audio track you can set to record clean track without reverb or input bus with reverb. You can find info on how to do it in acid manuał.

Brackets wrote on 2/4/2022, 5:38 AM

You need to use "input bus" and put reverb there. Than on audio track you can set to record clean track without reverb or input bus with reverb. You can find info on how to do it in acid manuał.

That's it! You're a genius! Heartache over!

Thanks to everyone for their time and suggestions. Very much appreciated.
 

shkr wrote on 2/4/2022, 7:36 AM

great :)